Rectangular paper- I use old atlases. You could use pages from a big book, old maps, Newspapers, thick magazine paper, wrapping paper, basically any sort of strong paper (or paper-like material) you have lying around the house. You can also use square-shaped paper if you want, I just think the rectangular paper has a nice look to it.
Scissors
Tape- I use shipping tape, but desk tape will work fine too.
Something to use as bag handles; You can use chunky yarn, ribbon scraps, or even crochet some handles out of scrap yarn! I use pieces of a dyed mop head I had leftover from a crafts class in college (I was an education major haha, we had crafts class)
Hole Puncher
Marker-optional
Embellishments-optional
Step 1: Lay your paper out on your workspace. Fold the top of the bag down about half an inch and crease. Put a few pieces of tape along the fold just to hold it in place. This will be the brim of our bag. This fold helps structure the bag so your top isn’t flimsy and can hold the handles better.
Step 2: Find the center point and fold both sides of your paper in so they overlap each other, in the center. Tape down the length where they overlap. Pro Tip: I like to extend my tape past the top and bottom of my bag and fold it over into the inside, just to give it some more structure.
Step 3: Fold up the bottom of the bag. This fold will decide the width of the bottom of your bag. The bigger the fold the wider the bottom of your bag will be. This also will decide how tall your bag will be, the bigger the bottom of your bag, the shorter your bag will be.
Step 4: Fold in each corner of the bottom flap you just folded. Then fold in the sides in, just over the middle, so they overlap; tape everything securely. This is the bottom of your bag, you want it to be strong so your goodies don’t fall out!
Step 5: Flip your bag over so that you are looking at the front side. Punch 2 holes near the top of the bag for the handles to go into. You want to try to center your holes on the half-inch fold you made in step 1 and try to make them symmetrical. Be sure to go through both the front and back sides of your bag so your holes all lineup.
Step 6: Cut two handles the same length.
Step 7: Going from the outside of the bag into the inside; insert your handle material. Tie a big knot, so when you pull on the handle, it doesn’t pop back out. Put the other end of your handle material into the other hole on the same side of the bag. Tie a big knot. Repeat on the back side of the bag, keeping your handles the same length.
Step 7: Going from the outside of the bag into the inside; insert your handle material. Tie a big knot, so when you pull on the handle, it doesn’t pop back out. Put the other end of your handle material into the other hole on the same side of the bag. Tie a big knot. Repeat on the back side of the bag, keeping your handles the same length.Pro Tip: To help keep your handles the same length, before you tie your second knot for your second handle, hold up the bag by the handles and see where you need to put the knot.
Step 8: Now you can decorate or embellish your bag any way you would like. I always just write “Thank you” real big on the front side. You could use stickers, stamps, jewels, buttons, the embellishing options are nearly UNLIMITED! Just get creative and make the bag portray your personality or business branding.
Answers & Comments
Verified answer
Answer:
RECYCLED PRODUCT BAGS TUTORIAL.
Here’s what you will need
Rectangular paper- I use old atlases. You could use pages from a big book, old maps, Newspapers, thick magazine paper, wrapping paper, basically any sort of strong paper (or paper-like material) you have lying around the house. You can also use square-shaped paper if you want, I just think the rectangular paper has a nice look to it.
Scissors
Tape- I use shipping tape, but desk tape will work fine too.
Something to use as bag handles; You can use chunky yarn, ribbon scraps, or even crochet some handles out of scrap yarn! I use pieces of a dyed mop head I had leftover from a crafts class in college (I was an education major haha, we had crafts class)
Hole Puncher
Marker-optional
Embellishments-optional
Step 1: Lay your paper out on your workspace. Fold the top of the bag down about half an inch and crease. Put a few pieces of tape along the fold just to hold it in place. This will be the brim of our bag. This fold helps structure the bag so your top isn’t flimsy and can hold the handles better.
Step 2: Find the center point and fold both sides of your paper in so they overlap each other, in the center. Tape down the length where they overlap. Pro Tip: I like to extend my tape past the top and bottom of my bag and fold it over into the inside, just to give it some more structure.
Step 3: Fold up the bottom of the bag. This fold will decide the width of the bottom of your bag. The bigger the fold the wider the bottom of your bag will be. This also will decide how tall your bag will be, the bigger the bottom of your bag, the shorter your bag will be.
Step 4: Fold in each corner of the bottom flap you just folded. Then fold in the sides in, just over the middle, so they overlap; tape everything securely. This is the bottom of your bag, you want it to be strong so your goodies don’t fall out!
Step 5: Flip your bag over so that you are looking at the front side. Punch 2 holes near the top of the bag for the handles to go into. You want to try to center your holes on the half-inch fold you made in step 1 and try to make them symmetrical. Be sure to go through both the front and back sides of your bag so your holes all lineup.
Step 6: Cut two handles the same length.
Step 7: Going from the outside of the bag into the inside; insert your handle material. Tie a big knot, so when you pull on the handle, it doesn’t pop back out. Put the other end of your handle material into the other hole on the same side of the bag. Tie a big knot. Repeat on the back side of the bag, keeping your handles the same length.
Step 7: Going from the outside of the bag into the inside; insert your handle material. Tie a big knot, so when you pull on the handle, it doesn’t pop back out. Put the other end of your handle material into the other hole on the same side of the bag. Tie a big knot. Repeat on the back side of the bag, keeping your handles the same length.Pro Tip: To help keep your handles the same length, before you tie your second knot for your second handle, hold up the bag by the handles and see where you need to put the knot.
Step 8: Now you can decorate or embellish your bag any way you would like. I always just write “Thank you” real big on the front side. You could use stickers, stamps, jewels, buttons, the embellishing options are nearly UNLIMITED! Just get creative and make the bag portray your personality or business branding.
Hope it helps
Correct me if I'm wrong
Brianlest please