Whether the blades aren’t spinning or the fan is making tons of noise, most issues with an electric fan are caused by poor lubrication or blockages in the vents. To solve most problems with an electric fan, disassemble the fan, lubricate the central pin and bearings, and clean out the vent and motor case. Repairing an electric fan can be tough if the problem has anything to do with the motor itself, which may be dead if the fan makes no noise when it’s turned on and the blades don’t turn at all after cleaning and oiling the pin. Since electric fans tend to be inexpensive, it’s usually not worth it to bother trying to repair the motor on your own and you should consider simply buying a new fan.
Explanation:
pa brain less , Turn your fan on to make sure that the motor works. Plug your fan in and turn it on to the highest power setting. If the fan blades move a little or it starts to turn, the motor is probably still good. If you don’t hear anything, put your ear up to the middle of the case behind the blades. Press the button to turn the fan off and on again, this time listening closely for the motor. If you hear it humming or buzzing, your motor is likely still functioning.[1]
Check the fan in multiple outlets. It’s possible that the circuit breaker on an outlet was flipped and the fan simply wasn’t getting an electrical signal.
Tip: For most table and standing fans, it won’t be worth it to tinker with the engine to try and get it to start again. The motor is probably dead anyway. You’re better off just buying a new fan if the engine isn’t firing. Feel free to disassemble the engine if you really want to try it yourself though!
2
Unplug the fan and either unhook the blade guard or unscrew the pin. Pull the fan’s electrical cord out to keep it from turning on randomly while you’re working on it. Feel around the sides of the blade guards for clips that are holding the 2 parts together. If there are clips, unhook them and remove the front half. If you don’t see any hooks keeping the blade assembly together, try turning the circular center of the fan counterclockwise. If it loosens, unscrew it and set the front of the blade case down.[2]
The pin is the piece of metal in the center of the fan that the blades and case rotate around.
The blade guard, or blade casing, refers to the plastic or metal case that keeps people from getting hurt by the blades. On most fans, it either holds together with clips where the 2 pieces meet, or it relies on a cap in the middle to keep the case screwed tight.
If you see screws holding the case together, unscrew them with a screwdriver to remove the case that way.
Answers & Comments
Answer:
Whether the blades aren’t spinning or the fan is making tons of noise, most issues with an electric fan are caused by poor lubrication or blockages in the vents. To solve most problems with an electric fan, disassemble the fan, lubricate the central pin and bearings, and clean out the vent and motor case. Repairing an electric fan can be tough if the problem has anything to do with the motor itself, which may be dead if the fan makes no noise when it’s turned on and the blades don’t turn at all after cleaning and oiling the pin. Since electric fans tend to be inexpensive, it’s usually not worth it to bother trying to repair the motor on your own and you should consider simply buying a new fan.
Explanation:
pa brain less , Turn your fan on to make sure that the motor works. Plug your fan in and turn it on to the highest power setting. If the fan blades move a little or it starts to turn, the motor is probably still good. If you don’t hear anything, put your ear up to the middle of the case behind the blades. Press the button to turn the fan off and on again, this time listening closely for the motor. If you hear it humming or buzzing, your motor is likely still functioning.[1]
Check the fan in multiple outlets. It’s possible that the circuit breaker on an outlet was flipped and the fan simply wasn’t getting an electrical signal.
Tip: For most table and standing fans, it won’t be worth it to tinker with the engine to try and get it to start again. The motor is probably dead anyway. You’re better off just buying a new fan if the engine isn’t firing. Feel free to disassemble the engine if you really want to try it yourself though!
2
Unplug the fan and either unhook the blade guard or unscrew the pin. Pull the fan’s electrical cord out to keep it from turning on randomly while you’re working on it. Feel around the sides of the blade guards for clips that are holding the 2 parts together. If there are clips, unhook them and remove the front half. If you don’t see any hooks keeping the blade assembly together, try turning the circular center of the fan counterclockwise. If it loosens, unscrew it and set the front of the blade case down.[2]
The pin is the piece of metal in the center of the fan that the blades and case rotate around.
The blade guard, or blade casing, refers to the plastic or metal case that keeps people from getting hurt by the blades. On most fans, it either holds together with clips where the 2 pieces meet, or it relies on a cap in the middle to keep the case screwed tight.
If you see screws holding the case together, unscrew them with a screwdriver to remove the case that way.